How-To & Care

How to Install LED Strip Lights: Drivers, Channels and Diffusers

A step-by-step guide to installing LED strip lights for a clean, even line: planning the run, sizing the driver, choosing a channel and diffuser, and cutting and connecting the strip.

25mm x 9mm White Shallow Winged Square Aluminium LED Profile Havit Lightin
25mm x 9mm White Shallow Winged Square Aluminium LED Profile Havit Lightin

To install LED strip lights, plan the run and measure it, choose a strip and a matching low-voltage driver sized for the total wattage, mount an aluminium channel with a diffuser, cut the strip only at its marked cutting points, then stick it into the channel and connect it to the driver. The driver is the part people forget: LED strip runs on 12 V or 24 V DC and cannot be plugged straight into mains power.

This guide walks through each step, with real examples of strips, channels and drivers, so you end up with a clean, even line of light rather than a row of dots. If you have not chosen a strip yet, start with our guide to the best LED strip lights in Australia.

What you need before you start

A neat strip light installation has four parts, and each is bought separately.

Part What it does What to check
LED strip The light source, sold by the metre or reel Voltage (12 V or 24 V), watts per metre, IP rating, width
Driver Converts mains power to low-voltage DC Output voltage matches the strip, wattage with headroom, dimmable or not, indoor or weatherproof
Channel (aluminium profile) Holds the strip, draws heat away, gives a straight edge Fits the strip's width, surface or recessed, length
Diffuser and end caps Softens the LEDs into one line and finishes the ends Matches the channel model, opal or clear

Step 1: Plan the run and measure it

Decide exactly where the light will sit and where the light should land. Under a kitchen cabinet, a strip near the front edge lights the benchtop rather than the splashback. In a ceiling cove, the strip sits out of sight and washes light up and across the ceiling. Measure each section in millimetres, note any corners, and mark where power will come in.

Then decide where the driver will live. It needs to be somewhere you can reach later, such as inside a cabinet, above a cupboard or in an accessible ceiling space, and close enough to the strip to keep the low-voltage cable short.

Step 2: Choose the strip

Three things decide which strip suits the job.

  • Voltage. Most strip runs at 12 V or 24 V DC. 24 V is common for longer runs. The strip and driver must match.
  • Output. Strip is rated in watts per metre, and brightness rises with it. The Havit 14.4W IP20 Micro LED strip, for example, draws 14.4 W per metre and produces 1,150 lumens per metre, enough for task lighting under cabinets.
  • IP rating. An IP20 strip has no moisture protection and belongs in dry interior positions only. Near a sink, in a bathroom or outdoors, choose a strip with a weatherproof rating.

Dotless strips, which use tightly packed LEDs, give a smoother line in shallow channels. The Havit 10W CSP Dotless LED strip runs at 24 V, draws 10 W per metre, is 8 mm wide and is dimmable with the right driver. Browse all LED strips to compare outputs and ratings.

Step 3: Size the driver

Multiply the strip's watts per metre by the metres you are actually installing, not the length of the reel. Then choose a driver rated comfortably above that total. A driver running at its limit runs hot, and heat shortens its life.

Two worked examples:

  • 4 m of 10 W per metre strip is 40 W. A 30 W driver is too small. A 60 W driver leaves room to spare.
  • 3 m of 14.4 W per metre strip is 43.2 W. Again, a 60 W driver is the sensible choice.

The Havit 30W indoor LED driver suits a short run, such as a single cabinet, and comes in 12 V or 24 V output. It is a fixed-output driver and is not dimmable. If you want to dim the strip, choose a dimmable driver such as the Havit 60W DALI or TRIAC dimmable driver, which is also weatherproof. Compare the full range of LED drivers by wattage and output voltage. If you plan to dim, make sure the wall dimmer or controller uses the same dimming method as the driver.

Step 4: Choose the channel and diffuser

Strip will light up without a channel, but it will run hotter and show every LED as a bright dot, and each dot reflects in a glossy benchtop. An aluminium channel draws heat away along its length, protects the strip and gives a straight, finished edge. A diffuser on top turns the dots into a continuous line.

Surface or recessed?

A surface channel screws or clips onto the underside of a shelf or cabinet. The Havit 16mm x 12mm square profile is a compact surface option in 1, 2 or 3 m lengths. A winged channel has flanges that sit flush in plasterboard or joinery so the line of light looks built in. The Havit 25mm x 9mm white shallow winged profile takes strip up to 12 mm wide and 3 mm high, so the 8 mm dotless strip above fits it comfortably.

Check the width

The channel has to suit the strip, not the other way round. Check the strip's width against the channel's listing before you order. Diffusers and end caps are usually listed separately, so order the ones made for your channel. See the full range of aluminium channels and profiles.

Opal or clear?

An opal (frosted) diffuser gives the smoothest line and hides the LEDs best. A clear diffuser lets out more light but shows the dots. The deeper the channel, the further the strip sits from the diffuser, and the smoother the line looks.

Step 5: Cut, fit and connect

  1. Cut the channel to length with a fine-tooth blade, and plan joins for corners or natural breaks where they are least visible.
  2. Fix the channel in place with its clips or screws, or set winged channel into the plaster before finishing.
  3. Cut the strip only at the marked cutting points. Cutting between them breaks the circuit and everything past the cut stays dark. Plan the run to the nearest cutting point.
  4. Clean the channel and stick the strip down along its full length with its adhesive backing.
  5. Connect the strip to the driver on the low-voltage side, checking the positive and negative markings.
  6. Test before you close up, then fit the diffuser and end caps.

The mains side of the driver is a different matter. Connecting a driver to fixed wiring is work for a licensed electrician, and many installers prefer to place the driver and run the power at the rough-in stage of a renovation.

Common mistakes to avoid

  • Buying a driver for the reel, not the run. Size it from the metres you install, plus headroom.
  • Mismatched voltage. A 24 V strip on a 12 V driver stays dim or dark, and the reverse can destroy it.
  • Burying the driver. Sealed inside joinery, it cannot be reached when it needs attention.
  • IP20 strip in a damp spot. Moisture damages the circuit board, often patchily.
  • Bare strip on a glossy surface. Use a channel and diffuser to stop the dots reflecting.

For ideas on where strip lighting works best around the home, read five ways to use LED strip lighting.

Frequently asked questions

Do LED strip lights need a driver?

Yes, low-voltage strip needs a driver to convert mains power to 12 V or 24 V DC. Match the driver's output voltage to the strip and size its wattage above the total load.

Can I cut LED strip lights anywhere?

No. Cut only at the marked cutting points, or the section past the cut will not light.

Do I need an aluminium channel for LED strip?

It is not essential, but a channel draws heat away, protects the strip and, with a diffuser, turns the dots into one smooth line.

How do I hide the dots on LED strip lights?

Use an opal diffuser in a channel, choose a deeper channel so the strip sits further back, or use a dotless strip.

Can I install LED strip lights myself?

Many people fit the strip and channel themselves. Connecting the driver to fixed mains wiring should be done by a licensed electrician.

Plan your strip lighting with us

Lights For You stocks strips, channels and drivers that are made to work together, and our team at the Ashfield showroom in Sydney can help you check widths, voltages and wattages before you buy.

Shop our lighting range
Tri-colour, dimmable and designer options in stock — fast Australia-wide delivery.
Shop now →