Buying Guides

How to Choose an LED Driver: Constant Voltage, Wattage and Dimming

Match the output type, wattage, dimming method and IP rating, and an LED driver will run cool without flicker. This plain-English guide walks through each choice with worked examples.

Domus Lighting LED Drivers Domus DRIVER 12V DC IP67 Non-Dim
Domus Lighting LED Drivers Domus DRIVER 12V DC IP67 Non-Dim

To choose an LED driver, match four things to your lights: the output type (constant voltage at 12V or 24V, or constant current in milliamps), the wattage (the total load of every fitting on the run, plus spare capacity), the dimming method (non-dimmable, trailing edge, 0-10V or DALI), and the IP rating for where the driver will be mounted. Get those four right and the driver will run cool, the lights will not flicker, and the job will last.

This guide walks through each decision in plain English, with examples from the drivers we stock. To browse the range, see our LED drivers.

What does an LED driver do?

An LED driver is the power supply between your 240V mains and low-voltage LED lighting. It converts mains power into the steady low-voltage DC that LED strip, garden spikes, step lights and many other fittings need. Without the right driver, a low-voltage fitting will not work, and connecting a 12V fitting straight to 240V will destroy it.

Some fittings have the driver built in and connect straight to mains. Others, including almost all LED strip, need a separate driver. The product page tells you which: look for wording such as "driver required" or "12V DC".

Constant voltage vs constant current

This is the first and most important match. The two types are not interchangeable.

Constant voltage (CV) Constant current (CC)
What it holds steady The voltage, usually 12V or 24V DC The current, measured in milliamps (mA), such as 350mA, 500mA or 700mA
Typical use LED strip, garden spike lights, step lights, many low-voltage fittings Specific downlights and LED modules designed for a set current
How fittings connect Wired in parallel, each fitting across the same 12V or 24V supply Matched to the fitting's stated current, as the fitting's manufacturer specifies
What to check Voltage matches the fittings, and wattage covers the total load Current (mA) matches the fitting exactly, and the fitting falls within the driver's range

Most home projects use constant voltage. If your fitting's page lists a current in mA rather than a voltage, you need a constant current driver. The SAL Pluto Constant Current LED Driver is an example: 28W, with an onboard switch to select 500mA or 700mA output, and designed to suit the specific SAL fittings named on its page. That is typical of constant current drivers, which are usually paired with particular fittings.

12V or 24V?

For constant voltage, the driver's output must match the fittings. A 12V strip on a 24V driver will fail, and a 24V strip on a 12V driver will not light properly. Check the strip or fitting first, then choose the driver.

If you have a choice, 24V has an advantage on longer runs. At the same power, a 24V system draws half the current of a 12V system, which means less voltage drop along the cable. Voltage drop is what makes the far end of a long strip or garden run look dimmer than the start, so 24V lets a run be longer before that becomes visible.

How to size the wattage

Add up the wattage of every fitting or every metre of strip on the run, then choose a driver rated comfortably above that total, with roughly a fifth spare. A driver running at its maximum runs hotter, and heat is what shortens its life. Spare capacity also gives you room to add a fitting later.

A worked example from the product page of the Domus 24V IP20 dimmable driver: 24V strip at 14.4W per metre over 5 metres is 72W. A 60W driver is too small, so the 100W model is the right choice.

For large loads, several smaller drivers placed close to their fittings can work better than one large driver at the start of the run. Cable runs are shorter, voltage drop is lower, and if one driver fails it does not take out the whole installation. On the 12V side, remember that current rises quickly with wattage, so large 12V loads need careful cable sizing by your electrician.

Choosing the dimming method

A driver is either non-dimmable or dimmable by one or more control methods. The control must match the driver, or you may see flicker, buzzing or lights that will not dim smoothly to a low level.

  • Non-dimmable: the simplest and most robust choice when you only need on and off.
  • Trailing edge (often called TRIAC dimmable): works with a compatible wall dimmer, the usual choice in homes. The SAL 12V Constant Voltage LED Driver 40W Dimmable is trailing edge dimmable, lists the SAL trailing edge dimmers it is designed for, and notes a 5W minimum load.
  • 0-10V and 1-10V: an analogue control signal, common in commercial lighting.
  • DALI: a digital control system used in commercial and automated buildings, where each driver can be addressed individually.
  • Multi-protocol: some drivers accept several methods. The Domus slim 24V dimmable driver supports TRIAC, 0-10V, 1-10V, 10V PWM and a simple potentiometer knob, in 30W, 60W or 100W.

Minimum load matters as much as maximum load on a dimmable system. A very small load on a large driver or dimmer can flicker at low levels. If your load is small, choose a smaller driver. For LED strip, a remote, wall panel or receiver may control the strip instead of a wall dimmer; see our LED strip controllers for the options.

Where will the driver live?

The IP rating of the driver must suit the location.

  • Indoors and dry (IP20): inside joinery, a ceiling void or a cupboard. The Domus 24V IP20 dimmable driver measures 100 x 36 x 18 mm, slim enough for a joinery void or pelmet.
  • Outdoors (IP65 to IP67): for gardens, decks and exposed positions. The Domus 12V IP67 non-dimmable driver comes in nine sizes from 20W to 500W, and the Vencha VDX60W is a 60W 12V IP67 driver in an aluminium body.

Wherever it goes, keep the driver accessible and ventilated. The driver is usually the first part of a low-voltage system to need attention, and the LEDs generally outlive it, so do not seal it inside a wall or bury it in insulation. Weatherproof is also not the same as submersible: mount outdoor drivers off the ground and away from pooling water.

Plug-in or hard-wired?

Some drivers are supplied with a flex and plug. The Domus 12V IP67 driver comes with a 1 metre flex and plug, and the SAL 40W dimmable driver with a 1.2 metre flex and 2-pin plug. Others have bare input leads for connection to fixed wiring. Any connection to fixed 240V wiring must be done by a licensed electrician, and a driver installed outdoors must be supplied from a suitable outdoor outlet or circuit. Ask your electrician before planning a garden or outdoor run.

Quick checklist

  1. Constant voltage or constant current? Check the fitting.
  2. For constant voltage, 12V or 24V? Match the fitting exactly.
  3. Total load in watts, plus roughly a fifth spare.
  4. Dimming: none, trailing edge, 0-10V, DALI or multi-protocol, matched to your control.
  5. Location: IP20 indoors, IP65 to IP67 outdoors, accessible and ventilated.
  6. Plug-in or hard-wired, and who will install it.

If you are planning LED strip, our guide to LED strip lights explains strip types, and the LED strips range lists the voltage and wattage per metre on each product page.

Frequently asked questions

What size LED driver do I need?

Add up the wattage of every fitting or metre of strip on the run, then choose a driver rated about a fifth higher than that total. For example, 72W of strip needs a 100W driver, not a 60W one.

Can I use a 24V driver with 12V LED strip?

No. The driver's output voltage must match the strip. A 12V strip on a 24V driver will fail.

What is the difference between a constant voltage and a constant current driver?

A constant voltage driver holds the voltage steady, usually 12V or 24V, and suits LED strip and most low-voltage fittings. A constant current driver holds the current steady, in mA, and suits specific downlights and modules designed for it.

Why do my LED strip lights flicker when dimmed?

The usual causes are a dimmer that does not match the driver, a non-dimmable driver on a dimmer, or a load too small for the driver or dimmer. Match the dimming method and size the driver to the load.

Can an LED driver go outside?

Only if it is rated for it. Use an IP65 to IP67 driver outdoors, mounted off the ground and away from standing water, and keep it accessible.

Need a hand matching a driver?

Browse all LED drivers, or bring your strip length and fitting list to our team. Lights For You supplies Sydney homes and trades from our Ashfield showroom, and we can size a driver with you before you order.

Shop our lighting range
Tri-colour, dimmable and designer options in stock — fast Australia-wide delivery.
Shop now →