LED lights flicker on a dimmer for one of a handful of reasons: the fitting is not dimmable, the dimmer was designed for old incandescent or halogen globes, or the total LED load sits outside the dimmer's minimum and maximum ratings. The fix is a dimmable LED fitting paired with an LED-compatible dimmer, usually a trailing edge type, loaded within its LED rating and set to a sensible minimum level. Buzzing has similar causes and usually goes away once the dimmer and the LED driver are properly matched.
This guide explains each cause in plain terms, how to match a dimmer to your lights, and what to check before you call an electrician back. If you are planning a whole room, our guide to layered, dimmable lighting covers where dimming makes the biggest difference.
Why LED lights flicker or buzz on a dimmer
An old incandescent globe is a simple load: a dimmer reduces the power, and the filament glows less. An LED is different. Every LED fitting has a small electronic driver that turns mains power into something the LEDs can use, and the dimmer has to work with that driver rather than with the LEDs directly. Most flicker and buzz comes from that hand-off going wrong.
1. The fitting is not dimmable
A non-dimmable LED on a dimmer may flicker, hum, refuse to dim or fail early. Check the listing says dimmable before you do anything else. Plenty of good fittings are not dimmable; the Telbix Edge LED batten, for example, says so in its name.
2. The dimmer was made for old globes
Older dimmers were built for incandescent and halogen loads. Many are leading edge designs with a high minimum load, and LED drivers often do not behave smoothly on them. Replacing the dimmer with an LED-rated model is the most common fix.
3. The load is too small
Every dimmer has a minimum load. LEDs draw so little power that two or three small fittings can fall below it, and the dimmer struggles to control them, which shows up as flicker at low levels or lights that glow faintly when switched off. The 3A DIM-400 dimmer, for example, lists a minimum load of 10 W for dimmable LED lighting.
4. The load is too big
A dimmer's LED rating is usually much lower than its headline rating. The same DIM-400 is rated to 400 W for incandescent globes but lists a maximum of 150 W for dimmable LED lighting. Add up the wattage of every fitting on the circuit and keep the total within the LED figure, not the bigger number on the box.
5. Ripple signals on the mains
Electricity networks in some areas send control signals down the mains, and these can make sensitive LED fittings flicker briefly even when everything else is right. SAL says its RippleSHIELD dimmer, paired with SAL rippleSHIELD downlights such as its Ripple Effect Shield downlight, is designed to suppress this ripple-induced flicker, which it notes is typically found in Queensland and New South Wales.
6. The wrong control system
Not every dimmable LED dims from a wall dimmer. Low-voltage strip lighting and some commercial fittings dim through their driver using a separate control signal such as 1-10V or DALI. A standard wall dimmer in front of a fixed-output driver will not dim it and can damage it.
Leading edge, trailing edge and universal dimmers
Mains dimmers work by trimming part of each wave of the alternating current. Which part they trim gives them their name.
| Dimmer type | How it works | Usually suits |
|---|---|---|
| Leading edge | Trims the start of each half-wave | Incandescent and halogen globes, iron-core transformers, some LEDs where the maker approves it |
| Trailing edge | Trims the end of each half-wave, more gently | Most LED drivers and electronic transformers; generally quieter with LED |
| Universal | Can run in either mode, set by the installer or automatically | Mixed or unknown loads, and replacing a dimmer in an existing home |
You will often see LED fittings described as TRIAC dimmable. That means they are designed to dim on a standard mains (phase-cut) dimmer. It does not tell you which edge the fitting prefers, so check the fitting's instructions or its list of tested dimmers.
How to match a dimmer to your LED lights
- Confirm every fitting on the circuit is dimmable. One non-dimmable fitting can cause flicker across the whole circuit.
- Check the fitting's recommended dimmers. Many makers publish a list of dimmers they have tested. A dimmer on that list is the safest choice.
- Add up the LED wattage. Keep the total above the dimmer's minimum and comfortably below its LED maximum.
- Match the dimming type. Trailing edge suits most LED drivers. If you are unsure, a universal dimmer lets the installer choose.
- Set the minimum level. Many LED dimmers let you raise the lowest setting so the lights never drop into the range where they shimmer.
Dimmers worth knowing
For flexibility: the SAL Master Push Button Universal Digital Dimmer runs in trailing or leading edge mode, with a green light for trailing edge and red for leading edge, and has a programmable minimum brightness level. It also supports multi-way dimming with SAL secondary dimmers.
For a simple swap: the Oriel Universal Dimmer LED Friendly Mechanism is listed for LED loads from 10 W to 250 W, fits Clipsal standard switch plates, and dims to around a tenth of full brightness with most LED loads. Oriel itself recommends testing with your fittings, which is sound advice for any dimmer.
For several switch positions: the Mercator Multi-Way Universal Rotary Dimmer is a trailing edge dimmer rated at 400 W of LED load.
Compare the full range of dimmer switches, and if you would rather dim from an app or by voice, see our smart switches and the smart lighting and switches guide.
Dimming LED strips and low-voltage lights
LED strip and most 12 V or 24 V lighting dims at the driver, not at the fitting. A fixed-output driver, such as the Havit 30W indoor LED driver, is not dimmable, and its listing warns that a mains dimmer in front of it will not dim the lights and can damage the driver. For a dimmable strip run, use a dimmable driver like the Havit 60W DALI or TRIAC dimmable driver, and make sure the dimmer or controller matches the driver's dimming method.
Quick troubleshooting checklist
- Flicker at low levels only: raise the dimmer's minimum setting, or check the load is above the dimmer's minimum.
- Lights glow faintly when off: often a sign the load is too small for the dimmer, or the dimmer suits a different load type.
- Humming from the switch or the fittings: try a trailing edge or universal LED dimmer, and check every fitting is dimmable.
- Brief random flickers at full brightness: may be mains ripple signals. A ripple-suppressing dimmer and matching fittings can help.
- Some fittings dim, others do not: check for mixed brands or a non-dimmable fitting on the circuit.
Changing a dimmer means working on mains wiring, so it is a job for a licensed electrician. Give them the brand and model of your fittings, and the dimmer they choose can be matched to them.
Frequently asked questions
Why do my LED lights flicker when dimmed?
Usually because the dimmer does not suit the LED driver, the total load is below the dimmer's minimum, or a fitting on the circuit is not dimmable. An LED-rated dimmer loaded within its range normally fixes it.
Do I need a special dimmer for LED lights?
Yes, use a dimmer rated for LED loads. Many older dimmers were built for incandescent and halogen globes and do not control LED drivers smoothly.
Is trailing edge or leading edge better for LED?
Trailing edge suits most LED drivers and tends to run quieter. Some fittings are approved for leading edge, so check the maker's recommended dimmers.
Can I put a non-dimmable LED on a dimmer?
No. It may flicker, buzz or fail early. Use fittings marked dimmable, or switch non-dimmable lights from a standard switch.
How many LED downlights can one dimmer handle?
Add up the wattage of the fittings and compare it with the dimmer's LED rating, not its incandescent rating. Stay above the minimum load and below the LED maximum.
Talk to us about dimming
Bring your fitting details to the Lights For You showroom in Ashfield, Sydney, and our team can help you match a dimmer to them before your electrician arrives. You can also shop the full range of dimmable lights online.



