LED Garden Spike Light Tri-Colour 12w in 316 Stainless Steel Havit Commercial - HCP-241120

LED Garden Spike Light Tri-Colour 12w in 316 Stainless Steel

A spike light pushes into soil and lights whatever it is aimed at - a tree, a wall, a hedge or a planted bed. It is the most adjustable fitting in garden lighting, and that is its main advantage.

A garden is never finished. Planting fills out, beds get reshaped, and a fitting aimed perfectly in its first season is often aimed into the back of a shrub by its third. A spiked fitting can be lifted and moved in a moment, which no fixed fitting can.

Seat it in firm ground below the loose surface layer. A spike pushed only into mulch will lean within a season, and a leaning fitting is the most visible fault in a garden lighting scheme - more so than the wrong beam or the wrong colour temperature.

Light output and colour

This is a tri-colour fitting: the colour temperature is selected at installation rather than fixed at manufacture. It runs at 3000K (845lm), 4000K (998lm), 5500K (1003lm).

That is genuinely useful rather than a specification-sheet feature. Colour temperature is the setting people most often get wrong and most regret, and it cannot be judged from a showroom - it depends on the surfaces in the room and on the light around it. A switchable fitting lets the decision be made in place, and changed if it is wrong.

⚠ Set every fitting on a run to the same value. Mixed colour temperatures in one space are obvious and look like a fault, which is the one way a tri-colour fitting can make a result worse rather than better.

Colour rendering is >80 CRI, which describes how faithfully colours appear under the light. It matters most where the light falls on planting, timber, brick or stone, all of which look flat under a poor-rendering source.

The beam spread is 60°.

Where it can be installed

At IP65 this fitting is rated for full outdoor exposure - rain, hosing and weather.

⚠ A weather rating is not a corrosion rating, and the two are confused constantly. The IP number describes water and dust ingress; what survives a coastal site is the material and the finish, and that is the thing to check within a few kilometres of the sea.

It is made from 316 stainless steel.

Powering and installing it

This is a 24V fitting, so it runs from a driver rather than directly from mains. Size the driver to the total load of every fitting on the run, with room to spare - a driver working at its limit runs hot, and heat is what shortens its life.

Low voltage is the usual choice in a garden because the cable is safer to run and easier to extend later. The trade is voltage drop: a long run gets dimmer towards its far end, and the answer is a shorter cable path or a heavier cable rather than a bigger driver.

Plan the cable route before anything is fixed. It is the part of an installation that cannot be changed afterwards without undoing the rest of it, and it is the reason otherwise finished jobs get left half done.

Before you order

Two checks save most of the problems that show up after an installation is finished. The first is where the fitting will actually be seen from: a light chosen for how it looks in a product photograph is being judged from a viewpoint nobody will ever stand in, and the same fitting can be discreet from the house and glaring from the street.

The second is what else is going in around it. A single fitting is rarely the whole scheme, and matching colour temperature and finish across everything in a space matters more to the result than the specification of any one item in it. Mixed colour temperatures in particular read as a fault rather than as a choice.

If you are unsure whether this suits what you are lighting, our team at Lights For You will talk it through against the actual space rather than the specification sheet.

Specifying and pricing this

This is part of the Havit Commercial range, which is priced on application rather than listed. Use the enquiry button on this page and we will come back with pricing for the quantity you need.

Commercial fittings are usually specified in quantity against a lighting plan, where the count, the colour temperature and the control method all have to agree across the job. We can check a schedule against what is actually available before it is issued.

⚠ Confirm availability before a specification is issued. Commercial ranges change, and a product written into a drawing that is no longer stocked is a change order later, when it is far more expensive to fix.

Frequently asked questions

Download Datasheet (PDF)

Download Datasheet (PDF)