Domus Reducer PLATE To Suit EXIT-REC

The Domus Reducer Plate is a passive mounting accessory for the EXIT-REC recessed exit sign — available in White or Black.

⭐ What it is for

⭐ A reducer plate closes the gap between a ceiling opening and a smaller fitting. ⭐ On a refit that is the common case: the existing hole was cut for an older, larger exit sign, and the replacement is smaller. ⭐ Without a plate the options are patching and repainting the ceiling, or leaving a visible gap. ⭐ With one, the new sign goes into the old hole and the ceiling is untouched. ⭐ It is a small part that removes a trade from the job.

⛔⛔ It publishes a voltage. It is a piece of sheet metal.

• ⭐ This product's record carries voltage = 24 V, bulb_type = Built-in LED and ac_dc = DC.
• ⛔ A reducer plate has no voltage, no LED and no direct current. ⭐ It has a colour, a shape and two dimensions.
• ⭐ WE CHECKED WHETHER THIS IS AN ISOLATED SLIP. ⭐ Restricting the test to unambiguously passive hardware — brackets, plates, arms, with anything naming a lamp or a wattage excluded — 15 of 15 publish at least one electrical field. ⭐ Wall brackets, post brackets and this plate all carry a voltage.
• ⭐⭐ SO IT IS A TEMPLATE DEFAULT APPLIED TO EVERY PRODUCT REGARDLESS OF WHAT IT IS, not a mistake on one record.
• ⚠ Harmless on a spec sheet a person reads. ⛔ Not harmless in a filter or a comparison table, where a mounting plate appearing under “24 V” is actively misleading — ⭐ and where a buyer filtering for 24 V components would be shown brackets.
• ⭐ WE HAVE NOT REPEATED THOSE FIELDS ON THIS PAGE. ⭐ What this product has is described below.

⭐ What you actually need to know before ordering

• ⭐ It suits the EXIT-REC range specifically — ⭐ check that is the sign you are fitting.
• ⭐ Two finishes, White and Black. ⭐ Match the sign, not the ceiling — a plate that matches the ceiling and not the fitting draws the eye to the fitting.
• ⚠ The plate's own dimensions are not published on this listing. ⭐ Since the whole point is covering a specific existing hole, that is the one figure worth confirming before you order. ⭐ Tell us the hole size you are covering and we will confirm it works.
• ⭐ It is a passive part: no wiring, no supply, no compliance role of its own. ⭐ The sign it fits carries the emergency approvals.

⭐ A note on ordering accessories with the fitting

⭐ Reducer plates are the sort of part discovered on the day, when the old sign comes out and the hole is bigger than expected. ⭐ They are inexpensive and specific — ⭐ so on a refit of any size, ordering a few alongside the signs costs little and saves a return visit. ⭐ If you tell us how many EXIT-REC units are going into existing openings, we will suggest a sensible number.

✅ What is published

Where it works

• ⭐ Refits — ⭐ an old larger hole, a new smaller sign.
• ⭐ Avoiding ceiling patching and repainting.
• ⭐ Ordered alongside EXIT-REC signs — ⭐ saves a return visit.
• ⚠ Not without confirming the hole size — ⭐ ask us.
• ⛔ Not for other exit sign ranges.

Specifying it

Passive reducer plate to suit EXIT-REC recessed exit signs. White or Black. No wiring, no supply, no compliance role of its own. ⛔⛔ ITS RECORD PUBLISHES A VOLTAGE, A BULB TYPE AND A DC SUPPLY. IT IS A PIECE OF SHEET METAL. We checked whether that is an isolated slip: restricting the test to unambiguously passive hardware — brackets, plates and arms, with anything naming a lamp or a wattage excluded — 15 OF 15 PUBLISH AT LEAST ONE ELECTRICAL FIELD. It is a template default applied regardless of what the product is. ⚠ Harmless on a spec sheet; not harmless in a filter, where a buyer looking for 24 V components would be shown brackets. ⭐ We have not repeated those fields here.

Supplied and supported by Lights For You.